The installation of external pond pumps is essential garden pond accessories, which allows continuous water circulation and supplies the water with sufficient oxygen. Outdoor electric well pump installations require some precautions before you can start pumping. The ground of the garden pond pump must be connected to a copper plate or about the 80cm long copper wire in the field. Never connect the ground wire to gas lines, as this may cause an explosion. Always switch off the power first and then connect the earthing of the water pump.
Never install a pond pump exposed to rain or direct sunlight. Extreme weather will shorten the life of your water pump. On top of that, you can get an electric shock. Acceptable conditions for externally installed pond pumps are at temperatures not lower than -10 ° C and not higher than 40 ° C.
Once the pump is working, make sure it does not run dry without carrying water. Also, exclude that the pump sucks up mud or sand from the bottom of the pond. Both malfunctions damage the engine.
Outdoor garden pumps should be thoroughly cleaned and maintained for trouble-free operation before being stored in a dry, frost-free place over winter. After hibernation and re-installation of the entire pump system in spring, it may happen that the engine does not start immediately. Such stalling or seizing of the impeller is possible due to encrustations in the engine head. Turn off the power! Then turn the center screw of the flywheel a few times to the left and right with a screwdriver and later try to start the pump again. Install a pond pump as close as possible to the garden pond or next to the fountain or waterfall. If the pump needs to be mounted further away from the garden pond, it is essential to pay attention to the suction capacity of the pump. Be sure to use standardized piping. If the pump is to feed one or more wells, it is advisable to reduce the diameters of the pipelines step by step from the pump to the suitable fountains. This increases the font pressure.
How do I install a garden pond pump?
Assembly
When installing the intake manifold, make sure that it does not protrude above the water level in hot, dry months, or that it can suck in sand or pond mud. The installation of an additional sand filter may be advisable for some flat garden ponds to prevent damage to the drive head. A sand filter installation also helps to ensure that the suction power does not decrease, and the water pressure remains stable.
To install the pond pump, choose a location where the motor around the pump is accessible for repairs and maintenance. Keep a distance of at least 30 cm around the water pump so that you can work with any tool on the pump motor. To prevent overheating of the pump, you should keep the same distance between the pump and the protective cover against rain and sun heat. Do not store easily flammable liquids near an electric well pump to avoid causing a fire. Anchor your garden pond pump with a stable, concrete foundation. A water pump should never be installed or jiggled, even after years of pumping.
To minimize leaks in the pipe system, avoid excessive use of L-pipe elements. This also reduces unnecessary resistance in the water flow. Do not start a water pump without suction water in the suction chamber, as this will damage the mechanical pump seal. After reinstalling, fill the suction chamber with water. Any remaining air in the intake manifold will be pumped out. If aspiration is not yet successful, there may still be water in the suction chamber. In this case, fill the intake manifold with water and turn the power on and off several times.
Even if your newly installed water pump begins to pump continuously, the water quality will not change immediately. It will take at least a few hours (or even days – depending on pond size) before the water circulation changes your ecosystem for the better. Periodically maintain outdoor pond pumps and inspect the power cord for damage from mice. Also, check that the pump is always at full power.
Now you should pay attention to these five things
- Many pumps should be placed at the lowest point
- if the hose is too short, it can easily be extended
- avoid flow-free zones
- an ideal is a place opposite the water inlet
- do not forget to do a thorough cleaning (before and after the season)
If you are still unsure, you are welcome to contact experts at any time.
Especially if there is a certain amount of fish in the pond, a good and reliable pump should be used. There are now many experts who take care of the planning from the implementation to your pond.
If you want to play it safe, leave the professionals and experts to work. There is no need to worry or worry about choosing the right pump and its correct placement. However, if you prefer to tackle the project yourself, you will undoubtedly find a lot of relevant information on the internet. With a little manual skill, the placement of a pond pump is not a problem.
To ensure perfect mixing, the use of a skimmer is worthwhile, especially for larger ponds. When installing, you should also make sure that stones do not obstruct the inlet of the pump. To ensure smooth operation, the hose should be tight. In some cases, the tubes will not fit on the pond pump.
Here you can help yourself with a stepped hose nozzle. Another handy tip is that if the hose cannot be attached to the port (hose too thin), simply immerse the tube in warm water and then stretch the tubing. Although you usually have a bit of trouble with the connection, you do not have to worry about the hose being stuck in the future.
Conclusion
In summary, it can now be said that placing a pond pump with the tips above and tricks should not be a problem. When buying, make sure you have good quality and sufficient delivery and delivery. Depending on the type of pump, a different place is recommended. Competent but staff will assist you, and there are also many professionals and experts who can help in the assembly.
Too short hoses can be easily extended, and of course, you will find the right solutions for many more problems. Excellent tips are also available on the Internet and the various forums. If you take these into account, installing a pond pump is not a big challenge.
Leave a Reply